SenderCAN® Plus

Our upgraded line of I/O modules designed to simplify data integration with your rugged applications.

Multiple part numbers and fixed input types have now been replaced with versatile software configurable inputs that simplify the customization process for developers & technicians.The SenderCAN^® Plus Series was designed with the same robust functionality as its predecessor, but now customers themselves can configure their I/O module to precise specifications, maximizing compatibility and efficiency across a wide array of applications.

The SenderCAN^® Plus Series is a game-changer for applications requiring extended I/O capabilities, often removing the need for an additional controller. Coupled with a free, intuitive Configuration Tool and a comprehensive J1939 library for custom message creation, the SenderCAN^® Plus Series empowers developers to tailor their application for reliable data integration in even the harshest environments.

Power Supply:
- Operating Voltage: 7-35 VDC
- Nominal Current: 30-40 mA
- Sleep Mode: Not Available
Analog Inputs :
- 12 Bit A/D Converter, resolution of 4096 bits scaled across measurement range
- 4 Software Configurable Inputs as Digital/Resistive/Voltage/Current
- Resistance Input Mode: Range is 0 to 10K ohm, In Resistive mode a 1K ohm internal pullup resistor to @5Vdc is enabled.
  
  Input Resistance Average Resolution
  
  0 to 1K ohm 1 ohm
  
  1K to 5K ohms 5 ohms
  
  5K to 10K Ohms 15 Ohms
- Voltage Input Mode: Range is –
  - - Low Range 0 – 4.6Vdc, 1.2mV resolution
    - High Range 0 – 32Vdc, 8mV resolution
- Current Input Mode: Range is 0 – 23mA, 0.006mA resolution. In 4-20mA mode a internal 200 Ohm Shunt Resistor is enabled, .
- Digital Switch Input Mode: Options are Open, Closed to B+, and Closed to B-
  - Switch Current – Closed to Battery Positive (3mA @ 12Vdc, 10mA @24Vdc)
  - Switch Current – Closed to Battery Negative (5mA @12Vdc, 5mA @24Vdc)
Frequency Input:
- Optically Isolated, 3Vrms Min, 30Vrms max, 30Hz – 10Khz
- Magnetic Pickup, Alternator, or Hall Effect sensor compatible
Digital Inputs:
- See Analog Inputs – Digital switch option
Digital Outputs:
- 2 Low-side FET’s (switches the negative side of circuit), 250mA Max (Use flyback diode or snubber on inductive loads)
- Configurable – controlled by CAN Message or internally generated Fault Status
- PWM control available when CAN controlled, PWM Frequency Rate = 3.9Khz, 0 – 100% duty cycle.
CAN Communications:
- 1 CAN Port – J1939 Protocol
- Software Selectable 120 ohm termination resistor
- Use built in library or create custom J1939 parameters
- Device firmware and Configuration is programmed over CAN using E-Com cable
Physical/Environmental:
- Enclosure Material: High impact ABS, epoxy filled
- Dimensions: 4.21″ Long x 1.30″ Wide x 0.71 High”
- Weight:
- IP rating: IP65 case exposed wire lead ends
- Relative Humidity: N/A
- Operating Temperature: -20° to +85°C (-4° to 185°F)
- Storage Temperature: -40° to +85°C (-40° to 185°F)
- Vibration: N/A
- Shock: N/A
- EMI/EMC: Complies with the following:
  - J1113-11 pulses 1c, 2a, 3a/b and 5a
  - EN 61000-4-2 ESD
  - EN 61000-4-3 Radiated disturbance
  - EN 61000-4-4 Fast transients
  - EN 61000-4-5 High energy transients
  - EN 61000-4-6 Conducted RF disturbance
  - CISPR 16-1-2, 4.3 Conducted Emissions
  - CISPR 16-2-3 Radiated Emissions

WARNING: This product may expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information about California Propsition 65, go to www.P65Warnings.ca.gov or visit our California Proposition 65 page.

Part Number	Model/Description	Notes	ShopEnovation
78700683	SenderCAN^® Plus	User configurable I/O Module designed to convert up to four switch, resistive, voltage, or current inputs into J1939 parameters that are broadcast on a CAN network used by any J1939 compliant device.	Buy Now
78700691	SenderCAN^® Plus Programming Kit (ECOM)	ECOM, harness with terminating resistor, as well as a small power supply to power the SenderCAN^® Plus (Download application tool)

SenderCAN® Plus

WARNING: This product may expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information about California Propsition 65, go to www.P65Warnings.ca.gov or visit our California Proposition 65 page.

Contact Us

Suggested Products

SK51

S35

PowerView® U35

CANBridge™

OpenView^TM S70

OpenPV® Software Platform